Polypropylene: Material (Membrane) Polypropylene: Pore Size: 0.2 μm: Sterility: Sterile: For Use With (Application) Sterilization of highly viscous solutions or solutions with high particulate loads: Housing Material: Polypropylene: Quantity: 50: Type: Syringe Filter: Volume (Metric) 10 to 100 mL (Sample) Diameter (Metric) 25 mm: Unit Size
Pore size: 0.2um. 1.10. $172.73. 66625. GH Polypro (GHP) Membrane Disc Filters Hydrophilic polypropylene membrane with maximum chemical compatibility when filtering both aqueous solutions and aggressive solvents. High recovery of critical proteinaceous samples due to low protein binding. HPLC certified. 50mm diameter. Pore size: 0.45um. 1.20
The pore size is usually determined by your application or objective. Mycoplasma removal can be performed using a 0.1 µm pore filter. Routine labora tory sterilization of most media, buffers, biological fluids and gases is usually done with 0.2 or 0.22 µm pore filter membranes. Clarification and prefiltration of solutions and solvents is best
GH Polypro (GHP) Membrane Disc Filters - Separations All purpose, universal membrane with maximum chemical compatibility for both aqueous solutions and aggressive solvents Specifications Filter Media Hydrophilic polypropylene Pore Size 0.2 and 0.45 µm Typical Thickness 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow Rate mL/min/cm 2 at 0.7 bar (70 kPa, 10 psi) 0.2 µm
GH Polypro (GHP) Membrane Disc Filters All purpose, universal membrane with maximum chemical compatibility for both aqueous solutions and aggressive solvents Specifications Filter Media Hydrophilic polypropylene Pore Size 0.2 and 0.45 µm Typical Thickness 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow Rate mL/min/cm 2 at 0.7 bar
The GD/X filter contains a unique prefiltration stack of 100% borosilicate glass. The prefilter will retain fine particles down to 0.7 μm, allowing difficult sample filtration with less hand force. The volume of the sample filtered is 3-7 times greater than an unprotected membrane. PP housing. Syringe filters can be autoclaved. Membranes:
GH Polypro (GHP) Membrane Disc Filters All purpose, universal membrane with maximum chemical compatibility for both aqueous solutions and aggressive solvents Specifications Filter Media Hydrophilic polypropylene Pore Size 0.2 and 0.45 µm Typical Thickness 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow Rate mL/min
What membrane filter pore size should I use for sterilization? Regardless of the membrane filter material, always use a 0.2 µm pore size membrane filter as the final filter for any sterilizing filtration. The 0.2 µm membranes used in Aijiren Tech™ Nalgene™ filters have been tested and shown to retain 100% of a challenge of 1 X 107
A pore size of 0.2 µm is small enough to remove microbes from solutions; a 0.45 µm ore size can remove larger particulates. Color and Grids White membrane filters may be plain or marked with square grids (outlined in black) that can help with enumerating particles.
Jun 1, 2003 · 2.2 Examination of membrane passing-through activity. An autoclaved MF-Millipore™ membrane filter (Millipore; diameter, 25 mm; pore size, 0.22, 0.3, or 0.45 µm) was placed and dried for 45 min on an LB agar or a blood agar plate. 10 µl of bacterial suspension (approximately 2×10 8 CFU ml −1 of saline) was spotted at the center of the filter on the agar medium without direct contact of a
tant. The smaller pore size Transwell membranes (0.4 or 3.0 µm) are primarily used in drug transport studies. Cell invasion, chemo-taxis and motility studies are usually done in Transwell membranes with 3.0 µm or larger pores. The ability of cells to migrate through pores of a membrane is dependent on the cell line used
Pore size: 0.2um. 1.20. $194.62. 66629. GH Polypro (GHP) Membrane Disc Filters Hydrophilic polypropylene membrane with maximum chemical compatibility when filtering both aqueous solutions and aggressive solvents. High recovery of critical proteinaceous samples due to low protein binding. HPLC certified. 13mm diameter. Pore size: 0.45um. 1.20
Hydrophilic polypropylene; Pore Size. 0.2 and 0.45 µm; Typical Thickness. 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow RatemL/min/cm 2 at 0.7 bar (70 kPa, 10 psi) 0.2 µm: 20; 0.45 µm: 31; Maximum Operating Temperature. 55 °C (131 °F) Minimum Bubble Point - IPA. 0.2 µm: 1 bar (100 kPa, 14.5 psi) 0.45 µm: 0.63 bar (63 kPa, 9.1 psi)
wwPTFE (water wettable PTFE), TF (PTFE, hydrophobic polytetrafluoroethylene), PVDF (hydrophilic polyvinylidene fluoride), and Nylaflo™ (hydrophilic nylon) membranes; Pore Size. 0.2 and 0.45 μm; Typical Thickness. wwPTFE Membrane; 0.2 μm: 280 μm (11.0 mils) TF (PTFE) Membrane; 0.2 μm: 139 μm (5.5 mils) 0.45 μm: 135 μm (5.3 mils) PVDF Membrane
Whatman Nuclepore Polycarbonate Black Membrane Filter, 0.2 µm Pore Size, 47 mm Circle, 100 Pack, 111156. Regular Price $213.58 Price $185.72. Add to Cart. Whatman Nuclepore Hydrophilic Membrane, 0.2 µm Pore Size, 142 mm Circle, 25 Pack, 112106. Regular Price $352.37 Price $306.00.