polypropylene housing GH Polypro membrane maximum operating temperature 55��C

wwPTFE Membrane Disc Filters - Mobile Phase Filtration

Hydrophilic polypropylene; Pore Size. 0.2 and 0.45 µm; Typical Thickness. 0.2 µm: 101 µm (4.0 mils) 0.45 µm: 114 µm (4.5 mils) Typical Water Flow RatemL/min/cm 2 at 0.7 bar (70 kPa, 10 psi) 0.2 µm: 20; 0.45 µm: 31; Maximum Operating Temperature. 55 °C (131 °F) Minimum Bubble Point - IPA. 0.2 µm: 1 bar (100 kPa, 14.5 psi) 0.45 µm: 0

amcPolyproFlow E--American Membrane Corporation

0.2, 0.45, 30, 60 µm: 0.55 m²/10 inch 1, 3 µm: 0.65 m²/10 inch 5, 10 µm: 0.72 m²/10 inch : Maximum Operating Temperature: 80 °C at 30 psi (2.1 bar) Maximum Differential Pressure: 60 psi (4.1 bar) at ambient temperature : Resistivity Recovery within 18 Mega-ohm: ≤120 L/10 inch length (at 1 L/min flow rate) Retention Efficiency

Polypropylene Nominal Prefilters - Membrane Disc Filters | Sterli

Max. Operating Temperature: 55°C (131°F) Food and Beverage Applications: Compliant for food contact under the applicable regulations in 21CFR177

Ideal for particulate removal prior to sample analysis (HPLC

Membrane: GH Polypro (hydrophilic polypropylene) Pore Size 0.45 µm Effective Filtration Area 0.28 cm2 Dimensions Overall Length (fully assembled with cap): 4.5 cm (1.8 in.) Capacities Sample Volume: 50 - 500 µL Filtrate Receiver Volume: 500 µL Hold-up Volume (membrane/support): < 2 µL Operating Temperature Range 0 - 40 °C (32 - 104 °F)

Handbook of PP & PP Composites | Polymers | Plastic

2 0 0 3 b y M a r c e l D e k k e r, I n c. 127.0.0.1 downloaded 0824740645.pdf at Mon Apr 16 16:07:49 ICT 2012 new trend is to build larger units with production capacity over 200,000 metric tons=yr. 2.9 POLYPROPYLENE APPLICATIONS As is obvious from the preceding discussion in this chapter, PP should really be considered a group of polymers

Fluorodyne® EX Grade EDF Filters - Pall Corporation

˝!$!%+*ˇ at a concentration of 10 7 CFU/ cm 2 membrane Housing, Vent Plug Polypropylene ... Maximum fOperating Temperature 40 °C Maximum Operating Pressure 5.2 ...

Maximum Continuous Service Temperature - Plastic Properties

Max Continuous Service Temperature. This is the maximum acceptable temperature above which mechanical properties (tensile strength, impact strength) or electrical properties (dielectric strength, linked to insulation properties) of a plastic part are significantly degrading, over the reasonable life time of the tested product.

Thermal Properties of Plastic Materials - Professional Plastics

temperature - 0.45MPa C Heat-deflection temperature - 1.8MPa C Lower working temperature C Specific heat J K-1 kg-1 Thermal conductivity W m-1 K-1 Upper working temperature C Cellulose Acetate CA 80-180 52-105 48-86 -20 -1900 0.16-0.36 @23C 55-95 Cellulose Acetate Butyrate CAB 140 73 62 <-40 - 0.16-0.32 @23C 60-100

Acrodisc® Units with Mustang® E Membrane - Endotoxin Removal

Filter Media: Mustang E membrane; Housing: Polypropylene; Pore Size. 0.2 μm; Inlet/Outlet Connections. Female luer lock inlet, male slip luer outlet; Membrane Bed Volume. 0.12 mL; Maximum Operating Temperature and Pressure. 2.1 bar (210 kPa, 30 psi) at 60 °C (140 °F) or 5.5 bar (550 kPa, 80 psi) at 21 - 24 °C (70 - 75 °F) Typical

(Mini Capsule)

Maximum Reverse Differential Pressure: 2.1 bar (30 psid) at 176°F/80°C Maximum Operating Temperature: PP & Gamma PP: 176°F/80°C HDPE: 140°F/60°C Minimum Burst Pressure: 8.3 bar (120 psid) at 77°F/25°C Sterilization: The filters can be sterilized by autoclaving for up to 25 cycles at 125°C (250°F) for 30 minutes, except for PE membrane

GH Polypro (GHP) Membrane Disc Filters - Mobile Phase Filtration

GH Polypro (GHP) Membrane Disc Filters Maximum versatility. Filters aqueous solutions or aggressive chemicals. ... Maximum Operating Temperature. 55 °C (131 °F)

Acrodisc® Syringe Filters with Versapor® Membrane

Maximum Operating Temperature 0.8 µm: 55 °C (131 °F) at 2.1 bar (210 kPa, 30 psi) 10 µm: 82 ºC (180 ºF) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure

Choice™ Polypropylene (PP) Syringe Filters

Economic Choice Syringe Filters are available in a variety of sizes and membrane types to meet any application need. Choice Polypropylene (PP) Syringe Filters 0.2 µm, 25 mm, 100 Pk. Choice Polypropylene (PP) Syringe Filters 0.45 µm, 25 mm, 100 Pk. Choice Polypropylene (PP) Syringe Filters 0.2 µm, 13 mm, 100 Pk.

Choice™ PVDF (Hydrophilic) Syringe Filters

Membrane: HPLC certified PVDF; Maximum operating temperature: 100 °C; Housing: Medical grade, virgin polypropylene; Autoclave: Sterilize by dry heat at 121 °C for 15 minutes; Applications. HPLC and organic-solvent sample preparation and clean-up; Protein-based samples with high non-specific binding; Environmental water samples; Chemical

3M™ NB Series Filter Bags Polypropylene Felt and Polyester

Table 3. Filter Bag Operating Parameters Operating Conditions Media Polypropylene Polyester Maximum Operating Temperature 180 °F (82 °C) 300 °F (149 °C) Maximum Recommended Flow Rate (gpm/lpm)** #1 Size 90 gpm (340 lpm) #2 Size 180 gpm (681 lpm) Maximum Forward Differential Pressure 35 psid @ 68 °F (2.4 bar @ 20 °C) Recommended Change-out