no leakage was observed the pressure was slowly ramped up to 3.4 barg ( 50 psig). No leakage or water breakthrough was observed up to a test pressure of 3.4 barg (50 psig). The test results demonstrate that the capsules retain their hydrophobic property and do not allow water to break through up to a pressure of 2.1 bar (30 psi).
A — HUMAN NECESSITIES; A61 — MEDICAL OR VETERINARY SCIENCE; HYGIENE; A61M — DEVICES FOR INTRODUCING MEDIA INTO, OR ONTO, THE BODY; DEVICES FOR TRANSDUCING BODY MEDIA OR FOR
Gross collector area AG m2 2,1 Inlet surface Aa m2 1,88 Absorber surface AA m2 1,90 Water content litres 1,2 Maximum operating pressure bar 10 Testing pressure bar 15 Optical efficiency ηo 0,773 Loss rating a1 W/m2.K 3,676 Loss rating a2 W/m2.K 0,0143 Stagnation temperature °C 180 Hydraulic connections mm 12 Pressure drop mbar See below
ghs 2-1/2 jg 3−b ghs 2-1/2 jg 4−b and 100 psi [7 bar] maximum speed for ammonia models. pump limited to 200 psi maximum pressure. mechanical seal lipseal ...
Maximum Operating Pressure: 350 psi, 24.1 bar; Minimum Burst Pressure: 1400, , 900, 700 psi, 96.4, 82.7, 62.1, 48.3 bar; Maximum Operating Temperature: 200 °F, 93 °C; Minimum Operating Temperature: 0 °F, -18 °C; Minimum Bend Radius: 1/2 - 4 inch, 12.7, 14.4, 25, 31.8, 63.5, 101.6 mm
2 1 0.5 0.25 0 0.75 4 6 8 10 12 AbsoLife™ Polygard™ 2 ) HDC II® PolyPro XL® FEATURES BENEFITS. MaxMedia construction for extremely high surface area. Higher product throughputs for extraordinarily long service life. Lower total filtration operating costs. Lower pressure drops for higher flow rates. Absolute-rated filter performance.
Maximum diaphragm operating temperature† Refer to page 5 Refer to page 5 Refer to page 5 Typical sound level at 70 psi (4.9 bar, 0.49 MPa) air @ 125 cpm 74 dBa 74 dBa 74 dBa Maximum air consumption 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) 28 scfm (0.672 m3/min) Air pressure operating range 30 to 100 psi (2.1 to 7 bar, 0.21 to 0.7 MPa) 30
Mar 01, 2015 · The maximum operating pressure is taken a 1.7 bar above normal operation. for example, the design pressure of a vessel that normall operates at 0-0.69 bar and 95-540 ⁰C is 2.76 barg (Turton et al., 2012). Towler suggests overdesign of vessel pressures by 5-10%. For vessels that will experience external pressure, design pressure is based on
Apr 03, 2009 · Comparison of the best NPMC in this work with a Pt-based catalyst. Polarization curves from H 2-O 2 fuel cell testing (P O 2 = P H 2 = 1.5 bar, 80°C, 100% RH) are shown for cathodes made with the best NPMC in this work, one with a loading of 1 mg cm –2 (circles) and another with a loading of 5.3 mg cm –2 (stars).
Membrane: Hydrophilic PTFE : Supports, core, sleeve: Polypropylene (PP) O-ring: E-FKM, silicone, EPDM, FKM: Retention rating: 15 nm, 20 nm, 0.1 µm, 0.1 µm DI : Cartridge connections: Code 0 (222 Flat), Code 5 (222 Fin), Code 6 (226 Flat), Code 7 (226 Fin) Maximum operating conditions: Maximum forward differential pressure: 5.5 bar (80 psid
Membrane tubing – Nafion® Maximum operating pressure: 3 Bar Absolute Operating fluid temperature range: 1 to 80°C (33 to 176°F) Pressure differential on tubing: 35 kPa (0 to 5 psid) @ 80°C (176°F) Negative pressure differential will collapse tubing and must be avoided Storage temperature range: -30 to 60°C (-22 to 140°F)
Maximum Operating Temperature 180ºF (82ºC) at 10 psid (0.7 bar) in water Table 4: Integrity Testing Micron Rating Specification 0.2 µm ≤ 50 cc/min at 30 psig (2.07 bar) 0.45 µm ≤ 50 cc/min at 15 psig (1.03 bar) Table 5: Flow Performance in Clean Water1 1 Data based on 10” length filter additional information
Membrane Material Polypropylene Nylon Polyethelyne Capsule Body Polyethylene Potting Material Polyethylene Filtration Surface Area 5” MDC – 4.1 ft 2 (0.38 m 2) 3” MDC – 1.8 ft 2 (0.17 m 2) 5” MDC – 4.8 ft 2 (0.45 m 2) 5” MDC –3.8 ft 2 (0.38 m 2) Maximum Operating Pressure 58 psig @ 77°F (4 bar @ 25°C) Maximum Operating
11304 0.8 white non 5.2 1.5 0.2 130 <1 11404 0.8 white black 5.2 1.5 0.2 130 <1 13004 0.8 black white 5.2 1.4 0.2 140 <3 * according to ASTM D 737; DIN 53 887, ISO 9237 Typical Performance of smaller pore size cellulose nitrate membranes Typ Pore Membrane Grid Flow Bubble Burst Thickness Extractables Recovery Coliform Retention
Filter Media: Mustang E membrane; Housing: Polypropylene; Pore Size. 0.2 μm; Inlet/Outlet Connections. Female luer lock inlet, male slip luer outlet; Membrane Bed Volume. 0.12 mL; Maximum Operating Temperature and Pressure. 2.1 bar (210 kPa, 30 psi) at 60 °C (140 °F) or 5.5 bar (550 kPa, 80 psi) at 21 - 24 °C (70 - 75 °F) Typical