225 psi (1.55 MPa) Applied Pressure 77 °F (25 °C) Operating Temperature 15% Permeate Recovery 6,5 - 7.0 pH Range Permeate flow: 2.250 GPD (8,5m3/d) Salt Rejection: 99,5 % Configuration: Spiral Wound Membrane active area: 285ft Maximum Applied Pressure: 600 psig (40 bar) Maximum Chlorine Concentration: < 0.1 ppm Maximum Operating Temperature
Maximum Operating Temperature 0.8 µm: 55 °C (131 °F) at 2.1 bar (210 kPa, 30 psi) 10 µm: 82 ºC (180 ºF) at 2.1 bar (210 kPa, 30 psi) Maximum Operating Pressure
Microglassfiber Syringe Filters Type- SYGF mdi Microglassfiber syringe filter are specially designed for clarification of extremely viscous samples that may clog a membrane filter. These syringe filters have micro-glassfiber filter encased in natural polypropylene housing with standard inlet (female luer lock) and outlet (male luer slip
Maximum Operating Temperature GHP Membrane: 55 ºC (131 ºF) PVDF, TF (PTFE), and Nylaflo Membranes: 100 ºC (212 ºF) Minimum Bubble Point – Water GHP Membrane 0.2 µm: 2.9 bar (290 kPa, 42 psi) 0.45 µm: 1.38 bar (138 kPa, 20 psi) PVDF Membrane 0.2 µm: 2.3 bar (230 kPa, 34 psi) 0.45 µm: 1.1 bar (110 kPa, 16 psi) Nylaflo Membrane
Maximum Operating Temperature: 55°C (131°F) Maximum Operating Pressure: 0.2 and 0.45µm is 6.9 bar (100psi) GF/0.45µm is 6.3 bar (90 psi) Typical Water Flow Rate (mL/min at 2.1 bar (30psi)) 0.2µm, 25mm is 60 0.45µm, 25mm is 65 0.45µm, 25mm GF is 60: Typical Water Flow Rate (mL/min at 0.7 bar (10psi)) 0.2µm, 13mm is 17 0.45µm, 13mm is 28 See full list on mgscientific.com
Pall GHP Polypropylene membrane will be discontinued effective October 31st, 2019. This discontinuation affects devices including syringe filters, filter plates, centrifugal devices and membrane filter discs. Syringe filters are attached to the end of a syringe to remove particles from a sample prior to analysis. Filtering liquids, the single-use devices force liquids through the filter either
What is the maximum operating temperature for the 17mm and 30mm syringe filters? A. The 17mm and 30mm syringe filters have a polypropylene housing, which allows them to withstand higher temperatures than an acrylic housing. The 17mm and 30mm's have a maximum operating temperature of 180°C. They are also able to be autoclaved.
GHP-SERIES (70V Input, Single/Dual Output) 2 2017-05-18 Specifications Absolute Maximum Ratings Input Voltage -0.5VDC to +120VDC Input Voltage +60VDC to +100VDC Output power Internally limited Output power 0 to Max. Rated Lead Temperature +300°C for 10 seconds Operating temperature -55°C to +85°C
AcroPak 300 Capsule Filters High flow rate venting with 0.2um PTFE membrane sealed in polypropylene housing. Inlet/outlet hose connections are 6.4 to 12.7mm stepped hose barbs. Effective filtration area: 300cm2. Maximum operating temperature: 60[degree]C at 2.1bar. Overall length: 10cm. $222.46. Pall Filter 1209
High precision filtration 0.01 µm filtration (filtering efficiency of 99.99%) is realized with the PTFE membrane cartridge element. (Clean gas strainer: Nominal filtration of 120 µm) Can be used under different environments This filter can be used under different environments with chemical resistant and heat resistant
0.069 MPa (0.69 bar; 10 psid) @ 23°C (73°F) Maximum operating temperature: 120°C (248°F) in inert gases Flow rating Refer to performance data PERFORMANCE DATA — 0.412 MPa inlet (60 psig) 0.206 MPa inle t Di˛erential Pressure (kPa) (30 psig) Di˛erential Pressure (psid) 0 10 20 30 40 50 60 0 20 40 60 80 1001 20 Wafergard SG F Micro Gas
Absolute Maximum Ratings Recommended Operating Conditions Input Voltage -0.5VDC to +160VDC Input Voltage +95VDC to +140VDC Output power Internally limited Output power 0 to Max. Rated Lead Temperature +300°C for 10 seconds Operating temperature -55°C to +85°C
Catalogue Number. HVLP04700. Trade Name. Durapore ®. Description. Durapore® Membrane Filter, 0.45 µm. Background Information. Durapore® membranes provide high flow rates and throughput, low extractables and broad chemical compatibility. Hydrophlic Durapore® membrane binds far less protein than nylon, nitrocellulose, or PTFE membranes.
Maximum Sample Volume: 500 µL Final Concentrate Volume: 15 µL Filtrate Receiver Volume: 500 µL Hold-up Volume (membrane/support): < 5 µL Operating Temperature Range 0 - 40 °C (32 - 104 °F) pH Range Nanosep Devices: 1 - 14 Nanosep MF Devices: 3 - 14 Maximum Centrifugal Force 14,000 x g Centrifuge Fits rotors that accept 1.5 mL tubes
Maximum Operating Temperature 55 °C (131 °F) Minimum Bubble Point - Water 0.2 µm: 2.9 bar (290 kPa, 42 psi) 0.45 µm: 1.38 bar (138 kPa, 20 psi) Maximum versatility. Filters aqueous solutions or aggressive chemicals. Low protein binding membrane gives high recovery of critical proteinaceous samples. HPLC certified. Provides assurance