Laboratory Filters - T300A013A - Advantec Unsupported Hydrophobic PTFE Membranes, 3.0 um, 13 mm; 100/Pk -- GO-36229-94. Supplier: Cole-Parmer. Description: This thin, highly porous PTFE membrane is inert to most chemically aggressive solvents, strong acids, and bases that may be incompatible with supported PTFE filters.
Catalogue Number. FHLP09050. Trade Name. Fluoropore. Description. Fluoropore Membrane Filter. Background Information. Our Fluoropore™ membrane is a hydrophobic, polytetrafluoroethylene (PTFE) polymer membrane bonded to a high density polyethylene support to improve the handling characteristics of the filter for normal applications.
Maximum Operating Temperature: 55°C (131°F) Maximum Operating Pressure: 0.2 and 0.45µm is 6.9 bar (100psi) GF/0.45µm is 6.3 bar (90 psi) Typical Water Flow Rate (mL/min at 2.1 bar (30psi)) 0.2µm, 25mm is 60 0.45µm, 25mm is 65 0.45µm, 25mm GF is 60: Typical Water Flow Rate (mL/min at 0.7 bar (10psi)) 0.2µm, 13mm is 17 0.45µm, 13mm is 28
wwPTFE Membrane Disc Filters - wwPTFE Membrane Disc Filters Maximum Operating Temperature. 55 °C (131 °F) Minimum Bubble Point - IPA. 0.2 µm: 1 bar (100 kPa ...
Catalogue Number. HVLP04700. Trade Name. Durapore ®. Description. Durapore® Membrane Filter, 0.45 µm. Background Information. Durapore® membranes provide high flow rates and throughput, low extractables and broad chemical compatibility. Hydrophlic Durapore® membrane binds far less protein than nylon, nitrocellulose, or PTFE membranes.
Maximum operating temperature 90°C (for Ø 70 mm cartridge, in water) 80°C (for Ø 83 mm cartridge, in water) Note: Savana PTFE can be sterilized by autoclaving up to 50 cycles at 125°C℃ or sterilized by steam-in-place up to 50 cycles at 135°C℃ for 30 minutes at less than 0.3 bar differential pressure. Savana PTFE Filter (Ø70 mm)
25 mm Syringe filter with 0.2 µm Supor® membrane with hydrophobic repel stripe, clear/green housing, sterile, FLL/MLL connectors. Specification. Pore Size. 0.2 µm nominal. Diameter (Metric) 25 mm. Effective Filtration Area (Metric) 2.8 cm². Housing Material.
Table 10.6 gives properties of a filter with hydrophilic ePTFE membrane (unrelated to Fig. 10.22) in the pore size range of 0.1–3 μm. Note the difference between the maximum operating temperatures of hydrophobic and hydrophilic membranes by comparing the data in Tables 10.4 and 10.6. The temperature drops from 260°C for hydrophobic to 100
It can be used under extreme chemical or temperature conditions that other membranes cannot withstand (up to 260 degree C). Trade name: mitex. Filter material: hydrophobic PTFE. Media brand name: mitex. Water flow rate, ml/min x cm squared: 126. Bubble point at 23 degree C: >=0.03 bar, air with water. Maximum operating temperature: 260 degree C
Pall 4501 Acrodisc Syringe Filters with PTFE Membrane, 25 mm Diameter, 0.45 µm Pore Size, Non Sterile, Hydrophobic PTFE Filter Media (1000): Science Lab Syringe Filters: Amazon.com: Industrial & Scientific
Catalogue Number. GVWP04700. Trade Name. Durapore ®. Description. Durapore® Membrane Filter, 0.22 µm. Background Information. Durapore® membranes provide high flow rates and throughput, low extractables and broad chemical compatibility. Hydrophlic Durapore® membrane binds far less protein than nylon, nitrocellulose, or PTFE membranes.
Maximum Operating Temperature 55 °C (131 °F) Minimum Bubble Point - Water 0.2 µm: 2.9 bar (290 kPa, 42 psi) 0.45 µm: 1.38 bar (138 kPa, 20 psi) Maximum versatility. Filters aqueous solutions or aggressive chemicals. Low protein binding membrane gives high recovery of critical proteinaceous samples. HPLC certified. Provides assurance
Jul 09, 2019 · The surface filter membrane is a hydrophobic filter with no support. It can be used under extreme chemical or temperature conditions (up to 260°C) that other membranes cannot withstand. Even under a very low pressure difference, it can ensure the unhindered passage of moist air or other gases, while the aqueous solution is not permeable.
Acrodisc 25mm Premium Syringe Filter Polypropylene housing. 0.45um GHP hydrophilic polypropylene membrane for maximum chemical compatibility fast flow rates low protein binding low levels of UV-absorbing extractables.
PVDF Membrane 0.2 µm: 140 µm (5.5 mils) 0.45 µm: 127 µm (5.0 mils) Nylaflo Membrane 0.2 and 0.45 µm: 127 µm (5.0 mils) Maximum Operating Temperature GHP Membrane: 55 ºC (131 ºF) PVDF, TF (PTFE), and Nylaflo Membranes: 100 ºC (212 ºF) Minimum Bubble Point – Water GHP Membrane 0.2 µm: 2.9 bar (290 kPa, 42 psi) 0.45 µm: 1.38 bar (138